Industrial Shredders, Briquetters & Drainage Presses from WEIMA

A WLK 4 single-shaft shredder shreds a wide range of waste from the production of plastic products for recycling and reuse.

An S7.20 Lift-up single-shaft shredder shreds textiles in Germany.

A W8.20 PowerLine for shredding beverage cans for recycling in Taiwan.

A combination of WL 4 shredder and C 150 briquetting press for shredding and subsequent briquetting of wood.

In Spain, PreZero has commissioned two new WEIMA FineCut 3000 shredders for shredding and recycling post-consumer waste.

In Hungary, a WLK 1500 single-shaft shredder shreds electronic waste, in particular circuit boards, for further recycling.

A W5.22 single-shaft shredder shreds plastic waste.

A WL 4 single-shaft shredder shreds old staves from wine barrels into wood chips for a wood chip heating system.

A WLK 1500 single-shaft shredder shreds various types of industrial plastic waste to produce recycled granulate.

In Slovenia, an S7.30 single-shaft shredder shreds plastic for recycling.

At Record Industry, production rejects in the form of vinyl and PVC waste are pre-shredded with a WL 4 and then processed into plastic granulate for new records using a granulator.

A C.200 drainage press for grinding sludge dewatering in Mexico.

A WEIMA W5.22 single-shaft shredder shreds paper in Slovenia.

A WEIMA S7.18 lift-up single-shaft shredder for shredding wood in France.

A WEIMA PowerLine 3000 single-shaft shredder shreds waste in South Korea.

A WEIMA PowerLine 1500 shreds post-consumer plastic in Portugal.

A WEIMA WLK 2000 single-shaft shredder shreds waste from firewood production. The shredded wood chips are used as fuel for a wood chip heating system, which in turn provides heat for the drying chambers in the firewood production facility.
Sustainability is key: the shredder is powered by solar energy and a combined heat and power unit (CHP), which ensures an environmentally friendly production process.

A PowerLine 3000 single-shaft shredder was recently installed in Jeongeup, South Korea for the shredding of waste to produce refuse derived fuel.

A WEIMA PowerLine 2500 single-shaft shredder shreds industrial waste for the production of substitute fuels at Green Partners in South Korea.

A WEIMA C 150 briquette press compacts wood dust produced during the production of beds. The special feature of this system is its direct integration into an extraction system, which enables clean disposal of the wood dust produced.

A WEIMA WL 20 with customised hopper shreds wood waste at a yacht manufacturer in England.

A WEIMA WLK 1500 single-shaft shredder with integrated extraction system for shredding plastic.

A WEIMA W5.18 single-shaft shredder shreds plastic.

A new WL 4 single-shaft shredder with integrated screw conveyor from Steiner for shredding wood.

A WEIMA W5.14 shredder shreds plastic in England.

A WEIMA W5.18 single-shaft shredder shreds IBC containers for further recycling.

A WEIMA PreCut 2500 single-shaft shredder shreds municipal waste.

A WEIMA PowerLine 3000 single-shaft shredder shreds plastic waste in Nova Scotia. The shredded material serves as a fuel source within the cement kilns.

A WLK 1500 single-shaft shredder shreds old wooden pallets at a company in England.

An S7.20 single-shaft shredder shreds PE lumps in a Remondis recycling plant in Sweden.

A WEIMA W5.18 single-shaft shredder shreds LDPE film at the RKW Group site in Hoogstraten.

A WEIMA WLK 1500 single-shaft shredder shreds wood pallets and waste wood.

A WEIMA WLK 15 single-shaft shredder shreds wood waste at a sawmill in Alabama in the USA.

A manufacturer in Texas known for creating high-end foam and fiberglass products for the marine, aerospace, wind and industrial sectors increased its impressive sustainability efforts by installing a TH 714 briquette press from WEIMA.

A WEIMA PowerLine 2500 single-shaft shredder shreds old tires at a recycling company in South Korea.

A PreCut 2000 single-shaft shredder shreds municipal waste at a Koran recycling company.

At Daewon Recycling in South Korea, an S7.30 lift-up single-shaft shredder shreds industrial and municipal waste for recycling.

A WEIMA PreCut 3000 single-shaft shredder shreds old textiles at a recycling company in South Korea.

A PowerLine 2500 single-shaft shredder is shredding municipal waste at a Koranic recycling company.

A WEIMA FineCut 3000 single-shaft shredder shreds municipal waste for use as RDF at a concrete plant in South Korea.

A WEIMA PreCut 2500 single-shaft shredder shreds large pulper strings from paper recycling.

In South Korea, a WEIMA WLK 1500 is used to shred old fishing nets and then recycle them.

A WEIMA W5.18 single-shaft shredder is shredding flower pots at a plastics recycler in the Netherlands. Now the customer uses a total of 4 WEIMA shredders for the different recycling lines in at his site.

A WEIMA S7.15 single-shaft shredder shreds wood waste from production into wood chips for energy generation.

A Carolina-based custom wood shop uses the Woodwolf 2000 to shred pallets on site.

A Canadian packaging company uses a WEIMA briquette press to manage cardboard dust. This briquette press is connected to an air system via rotary air lock, controlling dangerous dust within the plant.

A WEIMA WLK 1500 single-shaft shredder was recently installed in a sawmill in the Czech Republic to shred wood waste. The chips are then processed into wood pellets.

A WEIMA WLK 1500 single-shaft shredder was installed in combination with an Erema extruder to recycle plastic film.

A WEIMA S7.20 single-shaft shredder was recently installed to shred plastics.

A WEIMA W5.18 single-shaft shredder was recently installed to recycle plastics.

A briquette press was recently installed at a beverage facility. It's used to briquette the paper dust created during the manufacturing process. This maximizes cleanliness in the plant, as it's part of a larger, closed-loop dust collection process.

A WEIMA WL 8 single-shaft shredder with V-rotor technology is set up to shred hardwood lumber scrap.

A furniture company in North Carolina shreds furniture pieces made of wood. To do this, the company utilizes a (30hp) WEIMA WL 6 single-shaft shredder equipped with a V-rotor design.

Dust is a natural byproduct of cardboard shredding. With the help of an air system, dust is collected and transported to a WEIMA TH 814 briquette press. A rotary air lock and auto-on/off switch makes this process automatic, requiring minimal employee supervision. The briquettes are easily recycled and take up minimal space.

A WL 6 single-shaft shredder grinds CNC plywood skeletons and cutoffs. This scrap is a byproduct of the furniture manufacturing process and is easily shredded with V-rotor technology.

A WEIMA C 150 briquette press was recently installed to compress paper dust into compact briquettes. This machine is connected to an air system, which directly feeds the briquette press for a cleaner operation.

A WEIMA W5.22 single-shaft shredder shreds foam. This bulky, lightweight material is easily processed by the swing-ram technology, which holds the material close to the rotor for efficient shredding.

A U.S. company shreds baled cardboard scrap to be made into new products. The machine has an infeed conveyor that is loaded throughout the shift with a forklift. The rotor is a V-rotor design, ideal for handling tough or abrasive materials.

A WEIMA S7 series plastic shredder with hydraulic drive shreds HDPE plastic pipe offcuts (production waste) for recycling.

A WEIMA WLK 1500 single-shaft shredder with a tilting table shreds insulation boards at Unilin in Belgium.

A WEIMA S7.20 single-shaft shredder shreds post-consumer plastics.

A WEIMA PowerLine 3000 single-shaft shredder with hydraulic drive shreds plastic waste in Melbourne, Australia.

A WEIMA WL 4 wood shredder was installed at a German joinery.

Picture source: Georg Molinski, dds

A greek manufacturer of plastic pipes has added a WEIMA WLK 1500 shredder to its existing installation.

A WEIMA WLK 10 single-shredder grinds wood flooring offcuts. The wood chips are air-extracted and transported into a container.

A WEIMA WLK 1500 single-shaft shredder with conveyor belt has recently been installed by our service technicians in collaboration with our dealer CEMAC in Australia.

A WEIMA PowerLine 2000 single-shaft shredder with hydraulic drive by Hägglunds Bosch Rexroth shreds textile waste for recycling in South Korea.

A WEIMA WL 20 shredder shreds wood in England. The shredder was equipped with a hopper customized for the customer.

A WEIMA WL 10 single-shaft shredder for wood waste with dust extraction system has been installed in England.

A WEIMA S7.30 lift-up single-shaft shredder, including conveying technology and metal detection, has been in installed by our UK dealer Fercell in England.

A WEIMA ZM 30 four-shaft shredder shreds long wood strips at one of Europe's biggest saw mills in Wismar, Germany. The wood chips are used for energy generation at a power plant.

The recently installed M8.28 waste shredder performs great in Northern Italy!

Recently, a WEIMA W5.18 single-shaft shredder for plastic waste was commissioned at a customer's facility in Belgium.

Municipal solid waste fine shredding with two WEIMA FineCut single-shaft shredders

Recently, a WEIMA WLK 10 single-shaft shredder with electromechanical drive and WEIMA WAP gearbox for the size reduction of plastic film waste was installed in Romania.

Two new WEIMA FineCut 2500 secondary shredders for waste treatment were recently installed in Egypt.

Waste volume significantly reduced - mission accomplished: Nederman, a Romanian industrial air filtration company, chooses a WEIMA TH 800 M briquetting press to compact its steel chips.

A WEIMA S7.30 lift-up single-shaft shredder is a major part of transforming landfill-bound plastic scrap into composite products like railroad ties. This company prides itself on sustainability, and WEIMA is proud to be a part of their success.

A WEIMA FineCut single-shaft shredder is installed at a customer's plant in Virginia. This shredder is primarily used to pre-shred plastic waste for the production of composite structural materials.

This company in Quebec shreds, washes, and recycles household plastic waste for recycling purposes.

Superbon grinds plastic waste with a WEIMA granulator in Romania for recycling.

Zaplas shreds plastic waste with a WEIMA WLK 4 to sell recycled plastic granules

Fiddlehead Brewing Co. uses the PUEHLER E.200 by WEIMA to drain and compress out-of-spec, canned products in one easy step. The beer is drained from the aluminum cans as they are crushed into discs, making recycling a breeze. The machine was easily integrated into the canning line thanks to its plug-and-play nature.

Recently, a WEIMA PowerLine 3000 single-shaft shredder with hydraulic drive by Hägglunds Bosch Rexroth was installed in Korea.

A massive WEIMA PowerLine 3000 shreds industrial and MSW waste for secondary energy generation.

Plasticos Ojara S.A. produces all kinds of plastic hangers from recycled old plastic hangers with the help of WEIMA WLK 4.

Thanks to a WEIMA TH 800 M briquetting press, Ljunghäll AB can process aluminum chips into aluminum briquettes.

KOVIS from Slovenia finally found a solution for their steel chips: briquetting with WEIMA TH 800 M

T+T is a role model in the area of waste collection and disposal. They use a WEIMA WKS shredder to ensure that large agricultural films are shredded to a manageable size for further recycling and processing.

Satisloh is a global leader for ophthalmic and precision optics manufacturing technology. Plastic waste material from the production of optic lenses is briquetted with a WEIMA Vario 600 briquette press.

Plastika Kritis S.A., a leading European manufacturer of agricultural films based on the beautiful Greek island of Crete, shreds films and pipes using a WEIMA PreCut 2000 single-shaft shredder.

A hydraulically-driven WEIMA WKS 2000 single-shaft shredder shreds paper and corrugated cardboard waste for a Romanian customer.

A green-grey WEIMA WKS 1800 single-shaft shredder shreds post-consumer plastic scrap for a customer in Denmark.

A new customer in South Korea shreds circuit boards (WEEE waste) with a WEIMA WKS 2200 single-shaft shredder, equipped with a powerful Bosch Rexroth Hägglunds hydraulic drive.

Two WEIMA WKS 2200 single-shaft shredders grind mixed wood scrap at a Vietnamese customer.

A WEIMA PowerLine 3000 single-shaft shredder with hydraulic drive from Hägglunds shreds industrial waste for energy-generation.

A newly-installed WEIMA WLK 18 Jumbo shredder grinds plywood production scrap for a French customer.

A WEIMA WKS 1800 single-shaft shredder shreds post-industrial plastic film. After that, an EREMA extrusion line produces regranulate from the shredded material.

In Cambodia, a hydraulically driven WEIMA PowerLine 3000 shredder shreds commercial waste.

A WEIMA PowerLine 3000 single-shaft shredder, equipped with a powerful Bosch Rexroth Hägglunds hydraulic drive, shreds municipal solid waste and household waste in India.

The PowerLine 3000 is an ideal secondary shredder in a multi-stage system. At Ekoregion in Bełchatów, Poland, this universal single-shaft shredder shreds garbage bins, cans, plastics bottles and other waste for the production of high-quality refuse derived fuel (RDF).

KMK Paper in Kahramanmaras (Turkey) shreds paper production waste such as pulper rejects and ropes with two WEIMA WLK 25 Super Jumbo shredders to create refuse derived fuel (RDF). The RDF is then used to generate the energy needed for paper and corrugate production at the plant.

This PreCut 1500 single-shaft shredder is used for the recycling of synthetic rubber at a customer site in South Korea. It ensures the quality of the material for further processing such as sorting, classification and separation.

In Monterrey, Mexico, a WLK 15 Jumbo shreds plastic waste such as LDPE (low-density polyethylene) and HDPE (high-density polyethylene) for recycling purposes.

This South Korean customer shreds plastic waste such as PE (polyethylene) and PP (polypropylene) for the generation of energy at the cement plant with a WEIMA PowerLine 2000.

After pre-shredding and sorting, two WEIMA FineCut 2500 shredders shred municipal solid waste (MSW) and household waste at an Asian customer site. The final particle size is less than 50 millimeters.

At the dairy factory in Suhr (Switzerland) Emmi uses a PUEHLER G.300 ReWork drainage press to drain and compress rejected milk cartons from milk production.